Estimates seat occupancy and loading for restraint deployment decisions.
SENSOR GUIDE59/86
Identify the circuit first
ONE NAME. DIFFERENT SIGNALS.
Pin count is a clue, not proof. Confirm the exact architecture before resistance testing, applying voltage or judging the waveform.
TYPE 01CONSTRUCTION VARIANT
Pressure mat / bladder
Confirm wiring, pin count and service information before testing.
Seat loading changes pressure or resistance measured by the restraint module.
Reading the signal
Good waveform
Compare the measured signal with the specified input or command under the same operating conditions. Levels, timing and repeatability should match the installed design and a suitable verified reference. There is no universal waveform or scale for every version of this component.
Faulty waveform
An unexplained dropout, missing response, excessive noise or mismatch between command and feedback warrants further testing. First rule out a changed physical condition, incorrect probe reference, supply loss and an unsuitable scope setting; an unusual trace alone does not identify a failed component.
TYPE-SPECIFIC TESTS
+ Use scan classification data and approved simulators; never probe an inflator circuit.
+ Verify the specified supply, ground, bias or termination before judging the signal.
+ Repeat the test through the complete operating range.
EXPECTED
✓ Output matches this construction type
✓ Stable levels and repeatable response
✓ Agreement with related scan data
COMMON FAULTS
— Incorrect test method for the sensor type
— Supply, ground or signal-circuit fault
— Installation, target or calibration concern
TYPE 02CONSTRUCTION VARIANT
Strain-gauge seat frame
Confirm wiring, pin count and service information before testing.
Load cells measure deformation at seat mounting points.
Reading the signal
Good waveform
Compare the measured signal with the specified input or command under the same operating conditions. Levels, timing and repeatability should match the installed design and a suitable verified reference. There is no universal waveform or scale for every version of this component.
Faulty waveform
An unexplained dropout, missing response, excessive noise or mismatch between command and feedback warrants further testing. First rule out a changed physical condition, incorrect probe reference, supply loss and an unsuitable scope setting; an unusual trace alone does not identify a failed component.
TYPE-SPECIFIC TESTS
+ Inspect seat mounting and wiring; perform zero calibration with the seat empty.
+ Verify the specified supply, ground, bias or termination before judging the signal.
+ Repeat the test through the complete operating range.
EXPECTED
✓ Output matches this construction type
✓ Stable levels and repeatable response
✓ Agreement with related scan data
COMMON FAULTS
— Incorrect test method for the sensor type
— Supply, ground or signal-circuit fault
— Installation, target or calibration concern
TYPE 03CONSTRUCTION VARIANT
Capacitive / integrated module
Confirm wiring, pin count and service information before testing.
Electrodes and local processing classify occupant presence.
Reading the signal
Good waveform
Compare the measured signal with the specified input or command under the same operating conditions. Levels, timing and repeatability should match the installed design and a suitable verified reference. There is no universal waveform or scale for every version of this component.
Faulty waveform
An unexplained dropout, missing response, excessive noise or mismatch between command and feedback warrants further testing. First rule out a changed physical condition, incorrect probe reference, supply loss and an unsuitable scope setting; an unusual trace alone does not identify a failed component.
TYPE-SPECIFIC TESTS
+ Verify power, communication, seat trim condition and OEM calibration.
+ Verify the specified supply, ground, bias or termination before judging the signal.
+ Repeat the test through the complete operating range.
EXPECTED
✓ Output matches this construction type
✓ Stable levels and repeatable response
✓ Agreement with related scan data
COMMON FAULTS
— Incorrect test method for the sensor type
— Supply, ground or signal-circuit fault
— Installation, target or calibration concern
Correct theory and operation
HOW IT WORKS.
Understand the sensing method, circuit and controller strategy before interpreting data or replacing the component.
01
Measured condition
Estimates seat occupancy and loading for restraint deployment decisions.
02
Signal type
Digital networked sensor. Internal electronics condition the sensing element and transmit calculated data through a dedicated digital line or vehicle network.
03
Controller use
The receiving controller checks range, rationality and rate of change against related inputs before setting a fault or substituting a value.
04
Installation matters
Mounting, target condition, air gap, contamination, temperature, shielding or calibration may affect the result even when the circuit is intact.
Common mistakes
AVOID THE FALSE CLUE.
Condemning the sensor before verifying powers, grounds and communication.
Using a generic value instead of vehicle-specific service information.
Checking an unloaded circuit that fails only while operating.
Ignoring mechanical, installation or calibration causes.
Replacing the component without repeating the original test.
COMPLETE TEST SEQUENCE
Perform a complete module scan before disconnecting anything.
Verify powers, grounds, wake-up and communication.
Compare the sensor PID with related physical measurements.
Follow calibration, initialization and replacement procedures.
Repeat the original operating condition and confirm the repair.
DO NOT CONDEMN THE SENSOR
Prove its supply, ground, signal path, physical input and calibration before replacement. Vehicle-specific specifications always win.